RENT J LASHER RENTAL PER MONTH
Available*
Item # 630630000
Model # J LASHER
$1,200.00
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Rental
Rental Equipment
Line Construction- Placing
Lashers- Spinners
GMP General Machine Products
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
RENT GMP J LASHER RENTAL PER MONTH LASHER CAN BE AN F, J OR J2
The Cable Lasher is used to lash an aerial cable or numerous cables to a supporting strand or to an existing lashed cable with stainless steel lashing wire. Will lash any single or multiple aerial cables up to 3 in. diameter across on any suspension strand from 1/4 in. (6 mm) to 7/16 in. (11 mm). A factory modification will allow the lasher to accommodate 1/2 in. (13 mm) strand if necessary. Consists of a rotating drum supported on a carriage that provides the mounting for a driving mechanism, cable lifters, cable and strand rollers Each of two recessed magazines will hold a 1200 ft. coil of .045 in. (365 m of 1.1 mm wire) lashing wire (or 450 ft. of .065 in.) The Lashing Wire is fully recessed and covered by a gate. Features a fast setup procedure, quick coil loading, and automatic drum lock for easy span transfers and smooth forward travel. J2 Lashers make overlashing easy. Just push down on the strand roller knob, rotate it a quarter turn and you can lash additional cables together on previously lashed cable Positive internal gear to gear mechanism has no chains or belts to stretch, slip or break Constructed with heat treated, plated steel, stainless steel, brass and aluminum components. Contains sealed and oiless bearings to minimize maintenance and assure durability Pre-drilled and tapped at the factory for mounting of the lasher guard or "halo". For use when lashing in overgrown areas The lasher is furnished with a rugged lightweight storage chest with corrosion resistant hardware, recessed latches and a moisture proof, tongue in groove for maximum protection when not in use. Supplied with a 6 ft. bridle rope assembly and snap hooks, and an information and operation manual. The J2 Lasher's design also gives it maximum service life. The body is cylindrical to help it slip more easily through branches and obstructions. There is a built-in mechanical brake to prevent unintended reversal, an automatic drum lock for easy span transfers, an all-range tensioning device for optimum strand traction and high strength front and rear gates for tighter lashing.
The Cable Lasher is used to lash an aerial cable or numerous cables to a supporting strand or to an existing lashed cable with stainless steel lashing wire. Will lash any single or multiple aerial cables up to 3 in. diameter across on any suspension strand from 1/4 in. (6 mm) to 7/16 in. (11 mm). A factory modification will allow the lasher to accommodate 1/2 in. (13 mm) strand if necessary. Consists of a rotating drum supported on a carriage that provides the mounting for a driving mechanism, cable lifters, cable and strand rollers Each of two recessed magazines will hold a 1200 ft. coil of .045 in. (365 m of 1.1 mm wire) lashing wire (or 450 ft. of .065 in.) The Lashing Wire is fully recessed and covered by a gate. Features a fast setup procedure, quick coil loading, and automatic drum lock for easy span transfers and smooth forward travel. J2 Lashers make overlashing easy. Just push down on the strand roller knob, rotate it a quarter turn and you can lash additional cables together on previously lashed cable Positive internal gear to gear mechanism has no chains or belts to stretch, slip or break Constructed with heat treated, plated steel, stainless steel, brass and aluminum components. Contains sealed and oiless bearings to minimize maintenance and assure durability Pre-drilled and tapped at the factory for mounting of the lasher guard or "halo". For use when lashing in overgrown areas The lasher is furnished with a rugged lightweight storage chest with corrosion resistant hardware, recessed latches and a moisture proof, tongue in groove for maximum protection when not in use. Supplied with a 6 ft. bridle rope assembly and snap hooks, and an information and operation manual. The J2 Lasher's design also gives it maximum service life. The body is cylindrical to help it slip more easily through branches and obstructions. There is a built-in mechanical brake to prevent unintended reversal, an automatic drum lock for easy span transfers, an all-range tensioning device for optimum strand traction and high strength front and rear gates for tighter lashing.
