Factory Authorized Fiber Optic Products & Safety Equipment Sales, Service, Repair and Rentals
Save 5% Off All Pelsue Products (no coupon needed)
Polywater Fd-128 Gal Splicemaster Type Fd 02786804010 Case Of 4

Polywater Fd-128 Gal Splicemaster Type Fd 02786804010 Case Of 4

Available*
Item # 55461610
Model # FD-128
$430.92
Peac Financing financing available. Learn More
Qty:

* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)

  • Product Description
  • You Might Also like
  • Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
WIPES
Material and Supplies
Cleaners- Solvents
Cleaning Supplies
POLYWATER
CA Prop 65 Warning Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Product Description

American Polywater Fd-128 Gal Splicemaster® Type Fd™ 02786804010 Case Of 4 American American Polywater Fd-128 Gal Splicemaster® Type Fd™ 02786804010 Case Of 4

Fd™ Electrical Contact Cleaner A Fast-Drying Cleaner For General Industrial & Maintenance Use

1-Gallon (3.8 Liters) Can

Fd™ Electrical Contact Cleaner Is A Fast Drying, Multi-Purpose Industrial And Maintenance Cleaner. It Replaces Ozone-Depleting Cfc'S, Trichloroethane, Hcfc'S, Perchloroethylene And Other Carcinogenic Chlorinated Solvents. Fd™ Cleaner Effectively Dissolves Industrial Grimes, Greases, Lubrication Fluids, Silicone, Tars, Adhesives, And Fluxes.

Fd™ Electrical Contact Cleaner Evaporates Quickly Without A Residue. It Is Suitable For Use In Electrical Maintenance As A Replacement For 1,1,1-Trichloroethane. Transformer Oils, Corrosion Inhibitor Compounds, Silicone Grease, Semi-Conducting Paints, And Many Other Kinds Of Electrical Grime Clean Up Quickly With Fd™ Cleaner.

Typical Physical Properties Dielectric Strength (Astm D877) Relative Evaporation Rate Residue (Astm D 2369) Flashpoint (Astm D 56) Initial Boiling Point Specific Gravity Percent Aromatics Propellant (Aerosol Only) Cleaning Strength

36 Kv Fast < 100 Ppm ~0°F (< -5°C) 141°F (60°C) 0.69 < 0.1% Co2 Excellent

Advantages Multiple Packages To Fit Different End Uses Fast Evaporating Good General Solvency Power One Cleaner For Many Needs

Contains No Cfc'S Or Hcfc'S Contains No Chlorinated Solvents Harmless To Most Plastics Non-Conductive, Non-Corrosive, Non-Staining

Usage Directions & Performance

Fd™ Electrical Contact Cleaner Has A Variable Spray Head (Low, Medium, High) For Better Spray Control. Fd™ Is Suitable For Many Types Of Cleaning And Degreasing, Including Contact Cleaning, Cable Cleaning, And Communication And Electrical Maintenance Cleaning. It Can Be Used As A Spray, Wipe, Or Solvent Rinse. Fd™ Is Effective At Room Temperature. It Does Not Freeze And Can Be Used In Cold Weather Applications. Fd™ Is Authorized By The Usda For Use In Federally Inspected Meat And Poultry Plants.

Fd™ Electrical Contact Cleaner Has Good Solvency Power. Cleaning Time And Effectiveness Will Vary Based On The Contaminant And Cleaning Method. Wiping Or Agitation Cleans Faster Than Just Soaking. Experiment With Your Particular Contaminant And Conditions.

Fd™ Electrical Contact Cleaner Is Compared To Other Solvent Types In The Chart Below. A Stainless Steel Surface Is Coated With 50 Mils Of Contaminating Compound. The Surface Is Immersed And Lightly Agitated In Fd™ Solvent. The Time At Which The Contaminant Has Dissolved Is Noted. Silicone Electrical Insulating Compound Cleaner Cleaning Time Type Fd™ Cleaner < 2 Minutes Odorless Mineral Spirits 5 Minutes Isopropyl Alcohol > 5 Minutes

Hydrocarbon Lubricating Grease Cleaner Cleaning Time Type Fd™ Cleaner < 3 Minutes Odorless Mineral Spirits > 5 Minutes Isopropyl Alcohol >> 5 Minutes

Cable Filling Grease (Pe/Pj) Cleaner Cleaning Time Type Fd™ Cleaner 5 Minutes Odorless Mineral Spirits > 5 Minutes Isopropyl Alcohol >> 5 Minutes

Oxide Inhibiting Compound Cleaner Cleaning Time Type Fd™ Cleaner < 1 Minute Odorless Mineral Spirits < 2 Minutes Isopropyl Alcohol >> 5 Minutes

Fd™ Electrical Contact Cleaner Contains No Surfactants And Leaves No Residue Once Dried. For Precision Cleaning (Residue Free Use), Prevent Recontamination With Existing Grime By Finishing With A Fresh Wipe, Spraying Until The Solvent Runs Clear, Or Rinsing In A Fresh Bath Of Fd™ Cleaner.

Fd™ Electrical Contact Cleaner Is Fast Evaporating And Does Not Require Forced Air To Dry. In Areas Where Solvent Has Pooled, The Part May Be Wiped With An Absorbent, Lint-Free Towel. Evaporation Rate __________________________________ Fd™ Cleaner 40 Mg/Min. 1,1,1, Trichloroethane 50 Mg/Min. Perchloroethylene 20 Mg/Min. Isopropyl Alcohol 10 Mg/Min. Odorless Mineral Spirits .3 Mg/Min.

Compatibility

Fd™ Electrical Contact Cleaner Will Not Corrode Or Stain Metal Parts. It Does Not Tarnish Or Corrode Copper Per Astm D130 And D1729.

Fd™ Electrical Contact Cleaner Is Compatible With Most Plastics And Elastomers. Tables I And Ii Show The Effect Of Fd™ On Various Plastics And Rubbers.

Testing, Shown In Charts I And Ii, Is Based On A Soak Test Described In Astm D543. Fd™ May Temporarily Swell Some Rubber Compounds. These Rubbers Should Return To Their Original State After The Cleaner Has Evaporated. Immersion Will Affect Sensitive Materials More Than Incidental Contact Of A Spray Or Wipe. It Is Recommended That All Plastic Parts, Gaskets, Seals And O-Rings Be Tested For Specific Use And Exposure Method. Fd™ Compatibility With Plastics & Elastomers

Table I Aging 72 Hours At 50°C Type Of Plastic % Weight Change % Thickness Change Appearance Abs +0.81 0 Nc Acrylic +0.06 +0.15 Nc Cpe Thermoplastic +6.49 0 Nc Cpe Thermoset -6.51 0 Nc Delrin® +0.24 0 Nc Epoxy +0.08 0 Nc Nylon 101 +0.70 +0.27 Nc Polycarbonate +0.18 0 Nc Phenolic +6.99 +9.00 Nc Polyethylene +12.46 +3.78 Nc Polystyrene +31.49 +33.12 Sf Pvc -0.03 0 Nc Teflon® +0.07 0 Nc Tygon® -0.17 +6.62 Nc Ultem® 1000 -0.08 +0.27 Nc Valox® 420 +0.10 +1.12 Nc

Table Ii Aging 72 Hours At 50°C Type Of Elastomer % Weight Change % Thickness Change Appearance Epdm +100.88 +37.15 S Neoprene +2.36 +2.72 Nc Nitrile +2.00 +5.26 Nc Sbr +16.96 +31.53 Ss Silicone +65.97 +47.50 S Viton® +1.98 +4.43 Nc

Key: Nc=No Change Type Fd™ Is A Trademark Of American American American Polywater Corporation Sf=Softening Delrin® And Teflon® Are Trademarks Of Du Pont Ss=Slight Swelling Ultem® 1000 And Valox® 420 Are Trademarks Of G.E. Plastics S=Swelling Tygon® Is A Trademark Of Norton Performance Plastics

Viton® Is A Trademark Of Du Pont Dow Elastomers

Safety

Fd™Electrical Contact Cleaner Has A Low Level Of Toxicity. As With Any Solvent, Ventilation Should Be Sufficient To Keep Vapors At Safe Levels. Avoid Eye Contact And Excessive Skin Contact. Wash Hands With Soap And Water After Using.

Fd™ Electrical Contact Cleaner Is An Extremely Flammable Liquid. It Should Not Be Used On Energized Equipment. Fd™ Should Not Be Used For High Temperature Cleaning Or Exposed To Pilot Lights, Flames Or Heated Surfaces. Good Industrial Hygiene Practice And Appropriate Precautions Should Be Employed During Use. See Msds For Specific Details. Storage

Fd™ Electrical Contact Cleaner Is Classified As Flammable. Keep Containers Cool, Dry And Away From Sources Of Ignition And Oxidizing Materials. Do Not Expose Aerosol Cans To Direct Sunlight Or Temperatures Above 120°F (50°C). Do Not Puncture Or Incinerate Aerosol Cans. Aerosol Cans Are Freeze/Thaw Stable. This Product Has A Shelf Life Of Three Years.

You Might Also Like

Recently Viewed Items

img transfer pixel